How to use the Flyermate 3 in 1 Voltage Dispenser?

Charging a lipolymer battery is very time consuming and need a lot of attention.
That's why Flyermate designs the Voltage Dispenser for major charger among the RC industry to facilitate lipo charging process in a smart way.

If you want to shorten your charging time with a promising small device, surely at a very fair price, the Flyermate 3 in 1 Voltage Dispenser is your choice.

Let's start the set up step by step.

First, you need a digital charger which can be brought from http://www.swanghobby.com/ with free shipping worldwide.

The Flyermate 3 in 1 Voltage Dispenser does need a little bit calculation before we go.

One cell of Li-polymer battery is 3.7v

Therefore, a 7.4v battery is 2cells, and 11.1v is 3 cells and so on.

This 3 in 1 Voltage Dispenser support simultaneously charging 3 x 2cell lipolymers (22.2v) , 2 x 3cell (22.2v) lipolymers and 2 x 2 cells lipolymers (14.8v).

You have to determine the TOTAL voltage of your lipolymer batteries that you are going to charge in a same time. That's just two case, 22.2v or 14.8v.

Never connect ANY combination other than the 3 combination mentioned above. It will cause damage to your charger.

Secondly, connect the Flyermate 3 in 1 Voltage Dispenser correctly into the charger and batteries.

The connection for 3 x 2 cells (22.2v) and 2 x 3 cells (22.2v) setting.

Connect the batteries on the PCB broad with the balancing plug. This picture shows the connection of 2 x 3 cells. Connect the output cable with a T Plug back to your charger output.

Also connect to your charger's balancing output.

NOTE, leave the output cable next to the 2 x 2 cells NOT connected.
This cable is work for 2 x 2 cells case only.

After that, set the output AMP and output voltage to be 22.2v in charger.

Success! The digital charger shows the balancing status for the 6 cells!!
You are now charging two 3 cells lipolymer at the same time!! simultaneously

The connection for 2 x 2 cells (14.8v ) setting.
Now, connect 2 x 2 cells li-polymer on the PCB, and connect the cable next to the 2 x 2cell port to the charger's output plug. Leave the cable next to 2 x 3 cell not connected.
The setting is 14.8v as the output voltage, you can see that my digital charger showing totally 4 cells 's voltage status!! Have fun!

Error Message
If your connection of setting is wrong, you will get a error message from the charger, correct it and make it works!

Connection Break: Deal with it, you have to connect the batteries correctly, there are only

3 combination of connection. If you want to charge 1 battery, please remove the dispenser.

Over Voltage Deal with it, you have to set the output voltage correctly.

there are only two case, 22.2v (6S), remember it is for total 6cell in your setting. 2x 3 or 3 x 2

Or 14.8v (4S) , 2 x 2 only.

Sponsor: www.swanghobby.com - Free Shipping Worldwide
Manufacturer: www.flyermate.com Flyermate

Charger: G.T Power Dual Power Digital Charger

Li-polymer Battery: Flyermate M Series 11.1v 900mAh Li-Polymer Batteries, and Flyermate M Series 7.4v 900mAh Li-Polymer Batteries

You can buy the Flyermate 3 in 1 Voltage Dispenser at www.swanghobby.com .

Swanghobby.com reviews on G.T. Power A6 Balancing Charger

Swanghobby.com reviews on G.T. Power A6 Balancing Charger.






I had one of this,Good charger.




you can buy this G.T. Power A6 Balancing Charger at Remote Control Model Free Shipping Shop



Specification

Feature
- Microprocessor controlled high-performance Rapid charger/discharger for NiCD/ NiMH/ Li-Polymer/ Lilo/ LiFe/ Pb battery Include USB communicated analysis, (Monitor software supported)
- Temperature sensor and separate voltage detector for balance charge mode

SWANGHOBBY 89mm 5-Blades Ducted Fan + 3500Kv Brushless Motor

Swanghobby.com reviews on SWANGHOBBY 89mm 5-Blades Ducted Fan + 3500Kv Brushless Motor.







you can buy this SWANGHOBBY 89mm 5-Blades Ducted Fan + 3500Kv Brushless Motor at Remote Control Model Free Shipping Shop



Specification
Motor Type: 2217

Out Diameter: 89mm

Motor Shaft: 3.175

Weight: 120 grams (included brushless motor)

Kv: 3500

Fan Diameter: 74mm

Working Voltage: 11.1v 14.8v



Test Report

Voltage: 14.8v

Current: 45A

Pull: 860grams

Temperature: 98c / 10mins

Power: 660vA

Swanghobby.com reviews on CX450-02-04 Metal Tail Rotor Shaft

Swanghobby.com reviews on CX450-02-04 Metal Tail Rotor Shaft.







you can buy this CX450-02-04 Metal Tail Rotor Shaft at Remote Control Model Free Shipping Shop



Specification
CX450-02-04 Metal Tail Rotor Shaft

APC Propeller - Where to buy APC Propeller?

Dear All, Swanghobby.com is now selling APC Propeller with FREE SHIPPING worldwide,
APC Propeller is a great manufacturer in the RC Industry.

We can divide the APC Propeller into 2 major categories and its sub-category

1. APC Electric Propeller
2. APC Nitro Propeller

While under the APC Electric Propeller Products, we can make some sub groups
Composite Propeller
Widen Composite Propeller
Slow Flyer Propeller
Carbon Propeller

Swanghobby.com is now offering the full range of APC Propeller.

What is the propeller parameter mean?
For example, a 11 x 8 propellers mean the lenght of the APC Propeller is 11 inch and the evolution is 8 inch.

APC Landing Products RC thin electric composite model airplane propeller is designed for use with electric RC airplanes. Includes locating rings in various sizes and instructions on adaptation procedures.

APC Landing Products electric model airplane propellers have enjoyed strong acceptance and growth since their introduction in 1989. They are especially popular in RC pattern flying and RC airplane racing events. The performance and low noise advantages are largely spawned by the precision methods APC - Landing Products uses to design and manufacture APC electric RC airplane propellers.

APC - Landing Products preserves a close rapport with the RC aircraft competition community to benefit from technical interchange so important to improved RC airplane propeller designs. There is continuous evolution in RC aircraft design and engine performance. Consequently, propeller design must continuously evolve as well to keep pace with these improving technologies.

Due to APC's excellent quality and consistent performance APC - Landing Products' RC airplane propellers are perfect for any electric RC application from park flyers to 3D aerobatics to scale RC aircraft.

Note: This RC airplane propeller is designed only for use with electric motors. Do not attempt to use this propeller with glo or gas powered engines.

For more APC propeller products, please visit www.swanghobby.com

Review on Tower pro MG-995 Metal Gear Servo

Swanghobby.com reviews on Tower pro MG-995 Metal Gear Servo.

I have ordered 10 of these servos. They are Grreat. Plenty of power to fly my 38cc Gasser Plane and my Century Predator NX with 23cc motor.
I recommend them to all my friends. you can buy this Tower pro MG-995 Metal Gear Servo at Remote Control Model Free Shipping Shop

SpecificationSpecification
-Weight: 55.2 g
-Operating speed: 0.20 second / 60 degree (6.0v)
-Stall torque: 11.0kg/cm (6.0v)
-Temperature range: -20c~60c
-Dead band width: 4ms
-Operating voltage: 4.8v - 7.2v
-Connector wire length: 320mm
-Dimension: 40.6mm X 19.8mm X 37.8mm

Online Shopping

Review on 3e Model 11v 2200mAh 12C Li-Polymer Battery (Black)

Swanghobby.com reviews on 3e Model 11v 2200mAh 12C Li-Polymer Battery (Black).

a verry good battery. the cables have the right dimension to enable the output of the grat power the battery has. i am verry happy with this product. i use it in my rc car 1/18 size. you can buy this 3e Model 11v 2200mAh 12C Li-Polymer Battery (Black) at Remote Control Model Free Shipping Shop

Specification

Specification

-
mAh
: 2200

-
Discharge Rate
: 12C

-
Burst Rate
: 17C

-
Dimensions
:

103mm x 33mm x 28mm

-
Net Weight
: 177g

55

555

Review on HOBBYWING XERUN-120A-SD (V2.0) Electric Brushless Speed Controller (1/10)

Swanghobby.com reviews on HOBBYWING XERUN-120A-SD (V2.0) Electric Brushless Speed Controller (1/10).

This is the best ESC of ever!

120A of current with a stellar burst of 760A!!!
Most powerfull than a Mamba Max and MAMBA MONSTER too!!!!

It support sensored and unsensored brushless motor, so yuo can use it with:
- BUGGY : with a strong and lower kv unsensored motor like HOBBYWING eZRun 9T 4300kv;
- TOURING/F1 : with top kv motor sensored like HOBBYWING XERUN 3.5T 9100kv.

Extremely configurable with the possibility of PC USB connection with the HOBBYWING 2 In 1 LCD Program Box that allow you to set every single detail of this ESC.

In a word : FANTASTIC !!!

you can buy this HOBBYWING XERUN-120A-SD (V2.0) Electric Brushless Speed Controller (1/10) at Remote Control Model Free Shipping Shop

Specification

Feature

-
Compatible with all s
e
nsorless brushless motors and most of sensored brushless motors such as LRP, Novak, Orion, Feigao, etc.

-
Seamlessly change to sensorless working mode when the sensor cable is broken.

-
Lithium battery and NiMH battery supported.

-
Excellent start-up, acceleration and linearity features.

-
Firmware can be upgraded through an USB adapter on the Advanced Professional LCD Program Box (Optional equipment).

-
User programmable.
Easily programmed with only one button on the ESC and compatible with the 3 Digital LEDs Program Card and the Advanced Professional LCD Program Box.

Specification

- Continuous Current: 120A

- Burst Current: 760A

- Suitable Motor:
With 2 cells Lipo or 4-6 cells NiMH, 1/10 on-road: >=3.5T, 1/10 off-road: >=5.5T




With 3 cells Lipo or 7-9 cells NiMH, 1/10 on-road: >=5.5T, 1/10 off-road: >=8.5T

- Suitable Scale:
1/10, 1/12 on-road or off-road cars / trucks for competition race.




1/10, 1/8 rock crawler

- Input Voltage:
4-9 cells NiMH/NiCd or 2-3 cells Li
-
Po
lymer Battery

- BEC Output:
5.75V@3A linear mode built-in BEC

- Dimensions: 43mm x 36mm x 33mm

- Net Weight: 65g

Review on iMAX B5 Balancing Charger

Swanghobby.com reviews on iMAX B5 Balancing Charger.

I bought this charger for my RC18T FT and Rhino 1750mah 2S 25C. I received it VERY fast considering it came from HongKong and shipping was FREE. I open the package to find the box in prefect condition and hooked everything up. I first charged my Rhino 1750 2S which was perfectly balanced. (Thanks HobbyCity) Then I charged my GP 3300mah 6S Ni-Mh battery and it charged up and had more power then ever. I highly recommend this charger to anyone looking for a budget charger to get into the world of Li-Po.

you can buy this iMAX B5 Balancing Charger at Remote Control Model Free Shipping Shop

SpecificationB5 has an individual-cell-voltage balancer inside.
So it does not need any balancer separately
charging Lipo battery for cell balancing.


Maximum safety:
Delta-peak sensitivity:The automatic charge
termination program works on the principle of
the Delta-peak voltage detection.

Capacity limit:The charging capacity always
calculated by multiple of the charging current
and time.If the charging capacity exceeds the
limit the process will be terminated automatically
when you set the maximum value.

Processing time limit:you can also restrain the
maximum process time to prevent from any
possible defect.

Input power monitor:To protect the car battery
using as input power from being damaged the
voltage of it always monitored. Lf it drops below
the lower limit the process will be ended
automatically.

High-power and high-performance circuit

B5 employs the circuit that has maximum output
power of 50w. As a result it can charge up to 14
cells of Nicd/NiMH and 5 series of Li-poly
batteries with maximum current of 5.0A

Specification - Operating Voltage Range: 10.0-18.0 Volt
- Circuit Power: Max.50W
- Charge Current Range; 0.1-5.0A
- Current Drain For Balancing Li-Po; 200MAH/cell
- NiCd/NiMH Battery cell count: 1-14cell
- Li-ion/Polymer cell count: 15series
- Pb Battery Voltage: 6v,12v
- Weight: 280g
- Dimensions: 130 x 80 x 23mm

Review on HOBBYWING eZRun 12T/2030 7800Kv Sensorless Brushless Motor + 25A-SL-L ESC + LED Card

Swanghobby.com reviews on HOBBYWING eZRun 12T/2030 7800Kv Sensorless Brushless Motor + 25A-SL-L ESC + LED Card.






I've used this in my 1/18A 4WD buggy and it sure runs faster than brushed motor. It's so much better as little maintenance is needed and it's clean.
you can buy this HOBBYWING eZRun 12T/2030 7800Kv Sensorless Brushless Motor + 25A-SL-L ESC + LED Card at Remote Control Model Free Shipping Shop



Specification

Feature of 12T/2030 7800Kv Sensorless Brushless Motor - Top quality materials - Aluminum shell (case) - High quality magnets - Copper wires of high temperature endurance - Good quality bearings - Dustproof design - Low price but good quality, easy to use

Specification of 12T/2030 7800Kv Sensorless Brushless Motor - Rpm(Kv): 7800 - Working Voltage: 12v - Battery Type: NiCd/ Nimh/ Li-Polymer Battery - Shaft Length: 10mm - Shaft Diameter: 2mm - Motor Diameter: 20mm - Total Length: 40mm - Net Weight: 50g

Feature of 25A-SL-L E lectric S peed C ontroller - Compatible with all s e nsorless brushless motor - Use top quality electronic components to enhance the current endurance ability of the ESC - Excellent start-up, acceleration and linearity features - With 2 running modes (Racing mode and Forward/Backward mode) - With 4 steps of maximum reverse force adjustment - Proportional ABS brake function with 4 steps of maximum brake force adjustment, 8 steps of drag-brake force adjustment and 4 steps of initial brake force adjustment - With 4 start modes (Also called "Punch" ) from "Soft" to "Very aggressive" - Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / - Throttle signal loss protection / Motor blocked protection - With 8 steps of timing adjustment to get the best compatibility with various of motors - Easily program with only one button and compatible with pocket-sized program card

Specification of 25A-SL-L E lectric S peed C ontroller - Continuous Current: 2 5A - Burst Current: 90A - Suitable Motor: Sensorless Brushless motor , 12T and > 12T - Suitable Scale: 1/18 on-road or off-road cars / trucks for normal race or sportful race - Input Voltage: 4-9 cells NiMH/NiCd or 2-3 cells LiPo - BEC Output: 6V/1.5A - Resistance: 0.00 5 Ohm - Dimensions: 31.5 x 27.5 x 16 mm - Net Weight: 23 g(Without wires)

Feature of LED Card This program card is used to set the programmable parameters of brushless ESC, it has a friendly user interface, so you can set the programmable parameters very easily. It is pocket-sized, so you can bring it to the racing or flying field conveniently. This program card is suitable for the following ESCs: 1. XERUN Series Car ESC (Version 2.0) 2. EZRUN Series Car ESC (Version 2.0) 3. PLATINUM Series Helicopter/Aircraft ESC 4. SEAKING Series Boat ESC

Specification of LED Card - Input Voltage: 4.8-6V (If the ESC does not have a built-in BEC, you must use an additional battery pack to supply the program card) - Size: 88 x 58 x 14mm - Weight: 40g.

Package Content - 32T/3650-M 1200Kv Sensorless Brushless Motor x 1 - 25 A-RC E lectric S peed C ontroller x 1 - LED Card x 1

Reviews on Walkera 4#3B 4ch RTF 2.4Ghz Brushless Upgrade Edition Helicopter.

Swanghobby.com reviews on Walkera 4#3B 4ch RTF 2.4Ghz Brushless Upgrade Edition Helicopter.






Very Very nice Helicopter. I received it very fast and tried it out and from the first fly its still okay and flys very easy..

good helicopter for beginners but the charger could be better. it feels like it charges the battery only 80%
you can buy this Walkera 4#3B 4ch RTF 2.4Ghz Brushless Upgrade Edition Helicopter at Remote Control Model Free Shipping Shop



Specification

Features

1). Simplified 90o



swashplate with CNC-cut rotor head features durability and stability.


2). New 2.4G technology with the functions of automatic identification, precise code pairing and strong anti-jamming.


3). High performance 1220 motor powered by 3.7V 400mAh Lipo offers 7- to 9-minute flight time, depending on your flight mode

Specification

Main Rotor Diameter: 202 mm


Tail Rotor Diameter: 48 mm


Overall Length: 213 mm


All-up Weight: 48g (Battery included)


Drive Motor: KV11000(Brushless)


Tail Motor: N51 (Strong magnet)


Battery: 3.7V 400mAh Li-Po


Receiver: RX-2406A


Gyro: Built-in


Transmitter: WK-2401


Servo: weight 3.5g ; speed 0.11sec/60o(4.8V); torque 0.30kg/cm(4.8V);dimension 17.5 x 6.5 x 21.5mm

Package

Content

Walkera 4#3B Metal Brushless Helicopter Body (RTF w/ 4in1 controller & 2 x 3.5g Servo installed)



x 1

Walkera Transmitter WK-2401 4ch 2.4G)



x 1

400mAh

Battery (3.7V Li-polymer) )



x 1

Universal Charger (EU / US / AU /



UK all available!)





x 1

Adapter Cable for Flight Simulator System )



x 1

Quick Start Guide and Manual in English)



x 1

Review on Flyermate D130M Metal Gear HeatSink Digital Servo (Blue).

Swanghobby.com reviews on Flyermate D130M Metal Gear HeatSink Digital Servo (Blue).






In my last totally self made Graupner CHICO replica, I?ve used this small 12gr digital servos with metal gear.

This quiet good powered 1kg model with 50mm ailerons gives a lot of load to the servos but they fullfill my expactions completely! Smooth working and excellent re- addjustment to zero point. I can recommend this part 100%.




you can buy this Flyermate D130M Metal Gear HeatSink Digital Servo (Blue) at Remote Control Model Free Shipping Shop



Specification
Specification

-Weight: 17 grams

-Speed 4.8V:0.12sec/60o

-Speed 6V:0.11sec/60o

-Stall Torque (4.8V):2.2 kg/cm

-Stall Torque (6V):2.5 kg/cm

-Operating Voltage: 4.8-6V

Reviews on Flyermate 2000W 480Kv 70A A3732 Brushless Motor

Swanghobby.com reviews on Flyermate 2000W 480Kv 70A A3732 Brushless Motor.






I bought this motor with an 80amp ESC on Swanghobby.com.



Using 6 cell 4000mah lipo pack with a 12x13 APC racing prop. Pulls 49 amps for 1024 watts. Highest ESC timing & 16hz PWM settins, 8935 RPM. Great motor!! Doesn't even start to get warm at power level.



Some info I gleaned from testing for the moto-calc users.



No Load Current 2.6 amps at 25 volts

Internal resistance 0.051




you can buy this Flyermate 2000W 480Kv 70A A3732 Brushless Motor at Remote Control Model Free Shipping Shop



Specification
Specification

- Weight: 215grams

- Speed constant: 480KV

- Shaft diameter: 7.0mm

- Max. efficiency current: 70A

- Working voltage: 6~40V

- Power: 2000 W/60s

Review on SWANGHOBBY 3600Kv 5A Mini Brushless Motor

Review on SWANGHOBBY 3600Kv 5A Mini Brushless Motor

it is a nice motor for lama v4, co-comanche and other co-axial helicopter, whose weight does not exceed 230-250 grams. good quality, long shaft, no vibrations.
sizes:
diameter of rotor - 18mm
height w/o shaft - 23mm
diameter of shaft - 1.98-2.00mm
length of front shaft - 10mm
this motors have only one bad thing - they do not have any aperture for ventilation.

you can buy this SWANGHOBBY 3600Kv 5A Mini Brushless Motor at http://www.swanghobby.com/

Mini Brushless Motor 3600kv 5A Current Weight: 17grams Kv: 3600 Shaft Diameter: 2mm Size: 17mm x 20mm Current: 5A Suggested Application for ESKY LAMA

Review on HOBBYWING XERUN-120A-SD (V2.0) Electric Brushless Speed Controller (1/10)

Review on HOBBYWING XERUN-120A-SD (V2.0) Electric Brushless Speed Controller (1/10)



This is the best ESC of ever!
120A of current with a stellar burst of 760A!!!
Most powerfull than a Mamba Max and MAMBA MONSTER too!!!!
It support sensored and unsensored brushless motor, so yuo can use it with:
- BUGGY : with a strong and lower kv unsensored motor like HOBBYWING eZRun 9T 4300kv;
- TOURING/F1 : with top kv motor sensored like HOBBYWING XERUN 3.5T 9100kv.
Extremely configurable with the possibility of PC USB connection with the HOBBYWING 2 In 1 LCD Program Box that allow you to set every single detail of this ESC.
In a word : FANTASTIC !!!

you can buy this HOBBYWING XERUN-120A-SD (V2.0) Electric Brushless Speed Controller (1/10) at http://www.swanghobby.com/

Feature
- Compatible with all s e nsorless brushless motors and most of sensored brushless motors such as LRP, Novak, Orion, Feigao, etc.
- Seamlessly change to sensorless working mode when the sensor cable is broken.
- Lithium battery and NiMH battery supported.
- Excellent start-up, acceleration and linearity features.
- Firmware can be upgraded through an USB adapter on the Advanced Professional LCD Program Box (Optional equipment).
- User programmable. Easily programmed with only one button on the ESC and compatible with the 3 Digital LEDs Program Card and the Advanced Professional LCD Program Box.
Specification
- Continuous Current: 120A
- Burst Current: 760A
- Suitable Motor: With 2 cells Lipo or 4-6 cells NiMH, 1/10 on-road: >=3.5T, 1/10 off-road: >=5.5T With 3 cells Lipo or 7-9 cells NiMH, 1/10 on-road: >=5.5T, 1/10 off-road: >=8.5T
- Suitable Scale: 1/10, 1/12 on-road or off-road cars / trucks for competition race. 1/10, 1/8 rock crawler
- Input Voltage: 4-9 cells NiMH/NiCd or 2-3 cells Li - Po lymer Battery
- BEC Output: 5.75V@3A linear mode built-in BEC
- Dimensions: 43mm x 36mm x 33mm
- Net Weight: 65g

Review on Flyermate D130M Metal Gear HeatSink Digital Servo (Blue)

Review on Flyermate D130M Metal Gear HeatSink Digital Servo (Blue)

these servos are great for 450 heli cyclic. i got 3 of them on my cyclic of my exi 450 limited edition. they have great centering and they have little to no chatter of buzzing even at4.8volts i use them with a spektrum ar6100e and they are very responsive and they give very crisp snappy responses on rolls and flips. if you can get them get the metal gears becuse after about 10 to 15 cycles of hard 3d the white plastic gears develop some slop. but the metal gears stay slop free. i recomend them as a great sub for hitec 65mg and as a cheaper solution for the budget contious heli builders out there. get em and give em a try you wont be sorry.

you can buy this Flyermate D130M Metal Gear HeatSink Digital Servo (Blue) at http://www.swanghobby.com/

Specification

-Weight: 17 grams

-Speed 4.8V:0.12sec/60o

-Speed 6V:0.11sec/60o

-Stall Torque (4.8V):2.2 kg/cm

-Stall Torque (6V):2.5 kg/cm

-Operating Voltage: 4.8-6V

Reivew on Chewing Gum Style Mini Camera

Reivew on Chewing Gum Style Mini Camera

These cameras are great to mount on you remote control vehicle. I mounted mine on my Harley Davidson Motorcycle and shot a video of me driving home. The video was very clear with unexpected results of no vibration. The bike has quite a bit of vibration but it did not show in the video..

you can buy this Chewing Gum Style Mini Camera at http://www.swanghobby.com/

Specification
This Spy Camera can be installed in Remote Controlled Airplane, Helicopter, Vehicle and boat. Also can be used for your Spy mission!

Specification
- Video: 352 x 288 CIF resolution
- Video Format: AVI
- Support System: Window 98/ME/2003/Vista/OS/Linux
- Working Time: record for 4 hours.- 4 GB Internal Memory
- Battery: Built-in Lithium-Polymer Battery
- Charging Voltage: DC-5C (Charge by using a USB cable included)
- Weight: 17grams only

Hobbywing Ezrun ESC

Swanghobby.com is selling full range of Hobbywing Ezrun ESC.

HOBBYWING eZRun 12T/2030 7800Kv Sensorless Brushless Motor + 18A-SL ESC + LED Card

Motor Description: This is the EZrun-18A-SL-H + 12T Motor (KV 7800) + Program C ard Combo Set for RC cars and trucks. Feature: For: 1:18 RC Design: Sensorless-Based Operated with: Brushless ESC Specification: Turns: 12T KV: 7800 ESC Description: The EZrun series brushless controls include ESC of 18A for RC cars and trucks. Feature: Especially designed for RC car, with excellent start-up, acceleration and linearity features Compatible with sensorless brushless motor Use top quality of electronic components to enhance the current endurance and capacity of the ESC. 2 running modes (Racing mode and Forward/Backward mode) 4 steps of maximum reverse force adjustment Proportional ABS brake function with 4 steps of 4th – 11th maximum brake force adjustment, 8 steps of drag-brake force adjustment and 4 steps of initial brake force adjustment. 4 start modes (Also called “Punch”) from “soft” to “very aggressive”. Multiple protection features: Low voltage cut-off protection for lithium or nickel battery / Over-heat protection / Throttle signal loss protection / Motor blocked protection. 8 steps of timing adjustment. Waterproof and dustproof. Easily program with only one button and compatible with pocket-sized program card. (Please purchase at the bottom of this page) Specification: Cont. Current: 18A Burst Current: 50A Resistance: 0.01 ohm Suitable Car: 1/18, 1/16 car Suitable Brushless Motor: > 12T (2030 brushless motor) Battery: 4-9 Cell Ni-xx (NiMh or NiCd) or 2-3 Cell Li-Po BEC Output: 6V/1A Motor Type: Sensorless Brushless Motor Dimension: 31.5 x 27.5 x 15 (mm) Weight: 19g (Without wires) Package Content EZrun-18A-SL-H x 1 12T Senserless Brushless Motor x 1
Program Card x 1